[Home][email][Blog][House][Mach I Mustang][Pantera][Poetry][Jeep][351C Rebuild][AsaJay Inc.][Sam's Toy Chest]

351C Intake Manifold Selection Guide

This list provided by Dan Jones via the DeTomaso Email Forum:

In no particular order, here's a list of intakes for the 351 C:

Ford Boss 351 intake (p/n Dl Zx-9425-DA)
- low rise dual plane with Holley carb bolt pattern

Edelbrock Performer 351 4V (P/N 2665)
- low rise dual plane with Holley carb bolt pattern

Edelbrock F-351
- low rise dual plane with Holley carb bolt pattern
- obsolete, replaced by Performer 351 4V
- runner ports are smaller than intake ports for increased velocity

Edelbrock Performer 351 2V (PIN 2750)
- low rise dual plane with Holley carb bolt pattern

Ed elb rock Torker 351 (PIN 2760)
- high rise single plane with Holley carb bolt pattern

Edelbrock Victor 351 AH-lI (PIN 2990)
- air gap high rise single plane with Holley carb bolt pattern
- for raised port aluminum SVO heads (C302) on 9.2" deck height Cleveland and SVO blocks
- requires Windsor style water passages in heads
- waterneck section cast into manifold

Edelb rock Victor GN 351 -Y (2960)
- air gap high rise single plane with Holley carb bolt pattern
- for raised port aluminum SVO heads (Yates) on 9.2" deck height Cleveland and SVO blocks
designed for NASCAR Busch Series and Winston Cup engines (approved by NASCAR for Busch Series, Super Truck Series and Winston Cup)
no waterneck provisions in manifold.

Edelbrock Victor 351 -Y (2991)
- air gap high rise single plane with Holley carb bolt pattern
- for raised port aluminum SVO heads (Yates) on 9.2" deck height Cleveland and SVO blocks
- designed for circle track racing applications
- no waterneck provisions in manifold

Offenhauser Dual Port 351C-4V (6013-DP)
- dual port design (runners split into top and bottom sections, plenum split fore and aft, primaries feed longer path lower runners, secondaries feed shorter path upper runners), Holley carb bolt pattern

Offenhauser Dual Port 351C-4V (6014-DP)
- dual port design (runners split into top and bottom sections, plenum split fore and aft, primaries feed longer path lower runners, secondaries


feed shorter path upper runners), spread bore bolt pattern

Offenhauser Dual Port 351 C-2V (6011 -DP)
- dual port design (runners split into top and bottom sections, plenum split fore and aft, primaries feed longer path lower runners, secondaries feed shorter path upper runners), Holley carb bolt pattern

Offenhauser Dual Port 351 C-2V (601 2-DP or is it 6111 -DP)
- dual port design (runners split into top and bottom sections, plenum split fore and aft, primaries feed longer path lower runners, secondaries feed shorter path upper runners), spread bore bolt pattern

Offenhauser Turbo Thrust 351C
- tunnel ram with various tops
- part number: 5935 base, 5936 single quad top, 5938 dual quad top, 5993 single spreadbore top, 5937 Holley single Dominator top, 5983 3 Weber IDA top, 6102 special low volume single quad (Holley or spread bore) top

Oflenhauser Port-O-Sonic 351C-4V (6120)
- high rise single plane with Holley carb bolt pattern

Offenhauser Port-O-Sonic 351 C-4V (6121)
- high rise single plane with spread bore carb bolt pattern

Offenha user Port-O-Sonic 351 C-2V (6122)
- high rise single plane with Holley carb bolt pattern

Offenhauser Port-O-Sonic 351C-2V (6123)
- high rise single plane with spread bore carb bolt pattern

Offenhauser 360 Equa- Flow 351 C-4V (5964)
- high rise single plane with Holley carb bolt pattern
- short runner design with split plenum (side-to-side), plenum divider cut down and/or windowed

Offenhauser 360 Equa-Flow 351 C-4V (5966)
- high rise single plane with Holley Dominator carb bolt pattern
- short runner design with split plenum (side-to-side), plenum divider cut down and/or windowed

Offenhauser 360 "Single Quad rajet High Rise" 351 C-4V (5965)
- high rise single plane with spread bore carb bolt pattern
- probably same as Equa-Flow

Offenhauser Dial-A-Flow 351C-4V (6127)
- high rise single plane with Holley Dominator carb bolt pattern
- has interchangeable "turtles" to adjust plenum volume and floor shape

Offenhauser Dial-A-Flow 351C-2V (6128)
- high rise single plane with Holley Dominator carb bolt pattern
- has interchangeable "turtles" to adjust plenum volume and floor shape

Weiand X-Celerator 351 V-4V (7517)
- low rise single plane with Holley carb bolt pattern

Weiand X-Celerator 351 V-2V (7516)
- low rise single plane with Holley carb bolt pattern

Weiand Hi-Ram 351 C-4V dual Holley tunnel ram
- tunnel ram for dual Holleys
- p/n 1996 for '660' carbs
- p/n 2994 for Dominators

Holley Street Dominator 351 C-2V (300-12)
- low rise open plenum single plane with Holley (?)carb bolt pattern
- universal fit for both 2V and 4V heads

Holley Strip Dominator 351 C-4V (300-13)
- high rise air gap open plenum single plane with Holley carb bolt pattern

FPP 4145 (mfg by Blue Thunder) 351 C-4V (p/n 4145)
- high rise dual plane with Holley carb bolt pattern

FPP 4145B (mfg by Blue Thunder) 351C-4V (p/n 4145B)
- high rise dual plane with Holley carb bolt pattern
- same as FPP 4145 except the heat risers are blocked, the plenum divider is cut down one inch and the carb flange enlarged

FPP 4146 (mfg by Blue Thunder) 351 C-4V (p/n 4146)
- high rise dual plane with Holley carb bolt pattern
- same as FPP 4145 except the carb flange is machined for a Holley Dominator carb (1050 CFM)

Notes:

- Ford SVO markets various Edelbrock intakes under different p/n's.
- Still need info on:
factory Ford intakes (HO, CJ, etc) Australian Cleveland intakes Inglese Weber intake Hall Pantera Weber intake Ford intake for Autolite inline carbs 3x2 bbl intakes
Rousch racing intakes Bud Moore racing intakes supercharger intakes